HP 5400 zl Switch Series
Layer 2/3/4 switches which support integrated advanced capabilities in chassis (6-slot and 12-slot) form factor

Features & Benefits:

Software-defined networking

• NEW OpenFlow — is a key technology that enables software-defined networking by allowing the separation of data (packet forwarding) and control (routing decision) paths

Quality of Service (QoS)

• Advanced classifier-based QoS — classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a per-port or per-VLAN basis
• Layer 4 prioritization — enables prioritization based on TCP/UDP port numbers
• Traffic prioritization — allows real-time traffic classification into eight priority levels mapped to eight queues
• Bandwidth shaping —
  • Port-based rate limiting — provides per-port ingress-/egress-enforced increased bandwidth
  • Classifier-based rate limiting — uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each port
  • Reduced bandwidth — provides per-port, per-queue egress-based reduced bandwidth
• Class of Service (CoS) — sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ

Management

• Remote intelligent mirroring — mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl, 5400 zl, or 3500 Switch located anywhere on the network
• RMON, XRMON, and sFlow v5 — provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
• IEEE 802.1AB Link Layer Discovery Protocol (LLDP) — advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications
• Uni-Directional Link Detection (UDLD) — monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional link into a unidirectional one; this prevents network problems such as loops
• Management simplicity — provides common software features and CLI implementation across all HP ProVision-based switches (including the zl and yl switches)
• Command authorization — leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents activity
• Friendly port names — allow assignment of descriptive names to ports
• Dual flash images — provide independent primary and secondary operating system files for backup while upgrading
• Multiple configuration files — can be stored to the flash image
• NEW Comware CLI —
  • Comware-compatible CLI — bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
  • Display and fundamental Comware CLI commands — are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and fundamental commands provide a Comware-familiar initial switch setup
  • Configuration Comware CLI commands — when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command

Connectivity

• IEEE 802.3az Energy Efficient Ethernet — lowers power consumption in periods of low link usage (supported on v2 zl 10/100/1000 and 10/100 modules)
• IEEE 802.3af Power over Ethernet (PoE) — provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points, and security cameras
• IEEE 802.3at Power over Ethernet Plus — provides up to 30 W per port to IEEE 802.3 for PoE-/PoE+-powered devices such as video IP phones, IEEE 802.11n wireless access points, and advanced pan/zoom/tilt security cameras
• Prestandard PoE support — detects and provides power to prestandard PoE devices; see the list of supported devices in the product FAQ at www.hp.com/networking
• High-density port connectivity — provides up to 12 interface module slots and up to 288 wire-speed 10/100/1000 PoE-enabled ports or 96 10-GbE ports per system
• Jumbo frames — on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery services
• Auto-MDIX — automatically adjusts for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
• IPv6 —
  • IPv6 host — enables switches to be managed in an IPv6 network
  • Dual stack (IPv4 and IPv6) — transitions from IPv4 to IPv6, supporting connectivity for both protocols
  • MLD snooping — forwards IPv6 multicast traffic to the appropriate interface
  • IPv6 ACL/QoS — supports ACL and QoS for IPv6 network traffic
  • IPv6 routing — supports static and OSPFv3 routing protocols
  • 6in4 tunneling — supports encapsulation of IPv6 traffic in IPv4 packets

Performance

• High-speed, high-capacity architecture — 1 Tbps crossbar switching fabric provides intra-module and inter-module switching with 585.6 million pps throughput on the purpose-built ProVision ASICs
• Selectable queue configurations — allows for increased performance by selecting the number of queues and associated memory buffering that best meet the requirements of the network applications

Resiliency and high availability

• Virtual Router Redundancy Protocol — allows groups of two routers to dynamically back each other up to create highly available routed environments
• IEEE 802.1s Multiple Spanning Tree Protocol — provides high link availability in multiple VLAN environments by allowing multiple spanning trees; encompasses IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol
• IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking — support up to 144 trunks, each with up to eight links (ports) per trunk
• Distributed trunking — enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect to two switches using one logical trunk for redundancy and load sharing
• Optional redundant power supply (HP 5400 series) — provides uninterrupted power and allows hot-swapping of the redundant power supplies when installed
• Hot-swappable modules (5400 zl series) — permits modules, mini-GBICs, and power supplies in a redundant power supply configuration to be added or swapped without interrupting the network
• Sparing simplicity — HP zl-common accessories (interface modules and power supplies)
• Uplink Failure Detection — provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming

Layer 2 switching

• VLAN support and tagging — supports the IEEE 802.1Q standard and 2,048 VLANs simultaneously
• IEEE 802.1v protocol VLANs — isolate select non-IPv4 protocols automatically into their own VLANs
• GARP VLAN Registration Protocol — allows automatic learning and dynamic assignment of VLANs
• IEEE 802.1ad Q-in-Q — increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed campus or metro network
• MAC-based VLAN — provides granular control and security; uses RADIUS to map a MAC address/user to specific VLANs (requires v2 modules)
• Rapid Per-VLAN Spanning Tree (RPVST+) — allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+
• HP switch meshing — dynamically load balances across multiple active redundant links to increase available aggregate bandwidth; allows concurrent Layer 3 routing with v2 modules

Layer 3 services

• User Datagram Protocol (UDP) helper function — allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP
• Loopback interface address — defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
• Route maps — provide more control during route redistribution; allow filtering and altering of route metrics

Layer 3 routing

• Static IP routing — provides manually configured routing for both IPv4 and IPv6 networks
• Routing Information Protocol (RIP) — provides RIPv1 and RIPv2 routing
• OSPF — provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
• Policy-based routing — uses a classifier to select traffic that can be forwarded based on policy set by the network administrator (requires v2 modules)
• Border Gateway Protocol (BGP) — provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible

Security

• Access control lists (ACLs) — provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a per-VLAN or per-port basis
• Multiple user authentication methods —
  • IEEE 802.1X users per port — provides authentication of multiple IEEE 802.1X users per port
  • Web-based authentication — authenticates from a Web browser for clients that do not support IEEE 802.1X supplicant
  • MAC-based authentication — client is authenticated with the RADIUS server based on the client's MAC address
  • Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port — switch port accepts up to 32 sessions of IEEE 802.1X, Web, and MAC authentications
• Virus throttling — detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus from spreading across the routed VLANs or bridged interfaces without requiring external appliances
• DHCP protection — blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
• Secure management access — securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
• USB Secure Autorun (requires HP PCM+) — deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering
• Switch CPU protection — provides automatic protection against malicious network traffic trying to shut down the switch
• ICMP throttling — defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
• Identity-driven ACL — enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each authenticated network user
• STP BPDU port protection — blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
• Dynamic IP lockdown — works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
• Dynamic ARP protection — blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
• STP Root Guard — protects the root bridge from malicious attacks or configuration mistakes
• Detection of malicious attacks — monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks is detected
• Port security — allows access only to specified MAC addresses, which can be learned or specified by the administrator
• MAC address lockout — prevents particular configured MAC addresses from connecting to the network
• Source-port filtering — allows only specified ports to communicate with each other
• RADIUS/TACACS+ — eases switch management security administration by using a password authentication server
• Secure shell — encrypts all transmitted data for secure remote CLI access over IP networks
• Secure Sockets Layer (SSL) — encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
• Secure FTP — allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file
• Management Interface Wizard — helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
• Switch management logon security — helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
• Security banner — displays a customized security policy when users log in to the switch

Convergence

• IP multicast routing — includes PIM Sparse and Dense modes to route IP multicast traffic
• IP multicast snooping (data-driven IGMP) — automatically prevents flooding of IP multicast traffic
• LLDP-MED (Media Endpoint Discovery) — is a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network devices such as IP phones
• PoE allocations — support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to allocate PoE power for more efficient energy savings
• Auto VLAN configuration for voice —
  • RADIUS VLAN — uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
  • CDPv2 — uses CDPv2 to configure legacy IP phones
  • RADIUS VLAN — uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
  • CDPv2 — uses CDPv2 to configure legacy IP phones

Warranty and support

• Lifetime warranty — for as long as you own the product with advance replacement and next-business-day delivery (available in most countries)†
• Electronic and telephone support — limited electronic and telephone support is available from HP; to reach our support centers, refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to www.hp.com/networking/warrantysummary
• Software releases — to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available with your product purchase, refer to www.hp.com/networking/warrantysummary

Specifications:

	5406	5412	5406-44G-PoE+-2XG v2
Part Number	HP 5406 zl Switch with Premium Software (J9642A)	HP 5412 zl Switch with Premium Software (J9643A)	HP 5406-44G-PoE+-2XG v2 zl Switch with Premium Software (J9533A)
Included accessories
	1 HP 5400 zl Premium License (J8994A)	1 HP 5400 zl Premium License (J8994A)	1 HP 20-port Gig-T PoE+ / 2-port 10GbE SFP+ v2 zl Module (J9536A) 1 HP 1500W PoE+ zl Power Supply (J9306A) 1 HP 24-port Gig-T PoE+ v2 zl Module (J9534A) 1 HP 5400 zl Premium License (J8994A)
Ports
	6 open module slots Supports a maximum of 48 10GbE ports or 144 autosensing 10/100/1000 ports or 144 mini-GBICs, or a combination	12 open module slots Supports a maximum of 96 10GbE ports or 288 autosensing 10/100/1000 ports or 288 mini-GBICs, or a combination	44 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+) Media Type: Auto-MDIX Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 open 10GbE SFP+ transceiver slots 4 open module slots Supports a maximum of 16 10GbE ports or 140 autosensing 10/100/1000 ports or 100 mini-GBICs, or a combination
Power supplies
	2 power supply slots 1 minimum power supply required (ordered separately)	4 power supply slots 2 minimum power supplies required (ordered separately)	2 power supply slots 1 minimum power supply required includes: 1 x J9306A (HP 1500W PoE+ zl Power Supply)
Physical characteristics
	17.5(w) x 17.75(d) x 6.9(h) in (44.45 x 45.09 x 17.53 cm) (4U height)	17.5(w) x 17.75(d) x 12.1(h) in (44.45 x 45.09 x 30.73 cm) (7U height)	17.5(w) x 17.75(d) x 6.9(h) in (44.45 x 45.09 x 17.53 cm) (4U height)
Weight	23.55 lb (10.68 kg)	34.94 lb (15.85 kg)	46.08 lb (20.9 kg)
Memory and processor
Gigabit module	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM
10G module	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM
Management module	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM
Mounting
	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only
Performance
1000 Mb Latency	< 3.7 µs (FIFO 64-byte packets)	< 3.7 µs (FIFO 64-byte packets)	< 3.7 µs (FIFO 64-byte packets)
10 Gbps Latency	< 2.1 µs (FIFO 64-byte packets)	< 2.1 µs (FIFO 64-byte packets)	< 2.1 µs (FIFO 64-byte packets)
Throughput	up to 282.1 million pps	up to 564.2 million pps	up to 282.1 million pps
Routing/Switching capacity	379.2 Gbps	758.4 Gbps	379.2 Gbps
Switch fabric speed	379.2 Gbps	758.4 Gbps	379.2 Gbps
Routing table size	10000 entries (IPv4)	10000 entries (IPv4)	10000 entries (IPv4)
MAC address table size	64000 entries	64000 entries	64000 entries
Environment
Operating temperature	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed
Operating relative humidity	15% to 95% @ 131°F (55°C), noncondensing	15% to 95% @ 131°F (55°C), noncondensing	15% to 95% @ 131°F (55°C), noncondensing
Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)	-40°F to 158°F (-40°C to 70°C)	-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage relative humidity	15% to 95% @ 149°F (65°C), noncondensing	15% to 95% @ 149°F (65°C), noncondensing	15% to 95% @ 149°F (65°C), noncondensing
Altitude	up to 10,000 ft (3 km)	up to 10,000 ft (3 km)	up to 10,000 ft (3 km)
Acoustic	Power: 57 dB, Pressure: 40.2 dB ISO 7779, ISO 9296	Power: 64 dB, Pressure: 57.5 dB ISO 7779, ISO 9296	Power: 57 dB, Pressure: 40.2 dB ISO 7779, ISO 9296
Electrical characteristics
Frequency	50/60 Hz	50/60 Hz	50/60 Hz
	Achieved Miercom Certified Green Award
Description	Chassis ships without power supplies. Two power supply slots are available; three different power supplies are available. See power supply products for additional specifications.	Chassis ships without power supplies. Four power supply slots are available; three different power supplies are available. See power supply products for additional specifications.	One J9306A product is installed. One open power supply slot is available; three different power supplies are available. See power supply products for additional specifications.
Maximum heat dissipation	2450 BTU/hr (2584 kJ/hr), (max. non-PoE); 3700 BTU/hr (3903 kJ/hr) (max. using PoE)	4900 BTU/hr (5169 kJ/hr), (max. non-PoE); 7400 BTU/hr (7,807 kJ/hr) (max. using PoE)	2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE); 3700 BTU/hr (3903 kJ/hr) (max. using PoE)
Voltage	100-127/200-240 VAC	100-127/200-240 VAC	110-127/200-240 VAC
Idle power			215 W
Notes	Power supplies must be ordered separately. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.	Power supplies must be ordered separately. Two power supplies are required to power the J8698A chassis. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.	Idle power is the actual power consumption of the device with no ports connected. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.
Safety
	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950
Notes
	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).

	5412-92G-PoE+-2XG v2	5406-44G-PoE+-4G-SFP v2	5412-92G-PoE+-4G v2
Part Number	HP 5412-92G-PoE+-2XG v2 zl Switch with Premium Software (J9532A)	HP 5406-44G-PoE+-4G-SFP v2 zl Switch with Premium Software (J9539A)	HP 5412-92G-PoE+-4G v2 zl Switch with Premium Software (J9540A)
Included accessories
	3 HP 24-port Gig-T PoE+ v2 zl Module (J9534A) 1 HP 20-port Gig-T PoE+ / 2-port 10GbE SFP+ v2 zl Module (J9536A) 2 HP 1500W PoE+ zl Power Supply (J9306A) 1 HP 5400 zl Premium License (J8994A)	1 HP 24-port Gig-T PoE+ v2 zl Module (J9534A) 1 HP 20-port Gig-T PoE+ / 4-port SFP v2 zl Module (J9535A) 1 HP 1500W PoE+ zl Power Supply (J9306A) 1 HP 5400 zl Premium License (J8994A)	3 HP 24-port Gig-T PoE+ v2 zl Module (J9534A) 1 HP 20-port Gig-T PoE+ / 4-port SFP v2 zl Module (J9535A) 2 HP 1500W PoE+ zl Power Supply (J9306A) 1 HP 5400 zl Premium License (J8994A)
Ports
	92 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+) Media Type: Auto-MDIX Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 open 10GbE SFP+ transceiver slots 8 open module slots Supports a maximum of 32 10GbE ports or 284 autosensing 10/100/1000 ports or 196 mini-GBICs, or a combination	44 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T) Media Type: Auto-MDIX Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 open mini-GBIC slots 4 open module slots Supports a maximum of 16 10GbE ports or 140 autosensing 10/100/1000 ports or 100 mini-GBICs, or a combination	92 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+) Media Type: Auto-MDIX Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 open mini-GBIC slots 8 open module slots Supports a maximum of 32 10GbE ports or 284 autosensing 10/100/1000 ports or 196 mini-GBICs, or a combination>
Power supplies
	4 power supply slots 2 minimum power supplies required includes: 2 x J9306A (HP 1500W PoE+ zl Power Supply)	2 power supply slots 1 minimum power supply required includes: 1 x J9306A (HP 1500W PoE+ zl Power Supply)	4 power supply slots 2 minimum power supplies required includes: 2 x J9306A (HP 1500W PoE+ zl Power Supply)
Physical characteristics
	17.5(w) x 17.75(d) x 12.1(h) in (44.45 x 45.09 x 30.73 cm) (7U height)	17.5(w) x 17.75(d) x 6.9(h) in (44.45 x 45.09 x 17.53 cm) (4U height)	17.5(w) x 17.75(d) x 12.1(h) in (44.45 x 45.09 x 30.73 cm) (7U height)
Weight	75.36 lb (34.18 kg)	45.58 lb (20.68 kg)	74.86 lb (33.96 kg)
Memory and processor
Gigabit module	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 144 Mb QDR SDRAM
10G module	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM	ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR SDRAM
Management module	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB compact flash, 256 MB DDR SDRAM
Mounting
	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only
Performance
1000 Mb Latency	< 3.7 µs (FIFO 64-byte packets)	< 3.7 µs (FIFO 64-byte packets)	< 3.7 µs (FIFO 64-byte packets)
10 Gbps Latency	< 2.1 µs (FIFO 64-byte packets)	< 2.1 µs (FIFO 64-byte packets)	< 2.1 µs (FIFO 64-byte packets)
Throughput	up to 564.2 million pps	up to 282.1 million pps	up to 564.2 million pps
Routing/Switching capacity	758.4 Gbps	379.2 Gbps	758.4 Gbps
Switch fabric speed	758.4 Gbps	379.2 Gbps	758.4 Gbps
Routing table size	10000 entries (IPv4)	10000 entries (IPv4)	10000 entries (IPv4)
MAC address table size	64000 entries	64000 entries	64000 entries
Environment
Operating temperature	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed	32°F to 131°F (0°C to 55°C); 0°C to 40°C with J8706A or J8707A modules installed
Operating relative humidity	15% to 95% @ 131°F (55°C), noncondensing	15% to 95% @ 131°F (55°C), noncondensing	15% to 95% @ 131°F (55°C), noncondensing
Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)	-40°F to 158°F (-40°C to 70°C)	-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage relative humidity	15% to 95% @ 149°F (65°C), noncondensing	15% to 95% @ 149°F (65°C), noncondensing	15% to 95% @ 149°F (65°C), noncondensing
Altitude	up to 10,000 ft (3 km)	up to 10,000 ft (3 km)	up to 10,000 ft (3 km)
Acoustic	Power: 64 dB, Pressure: 57.5 dB ISO 7779, ISO 9296	Power: 57 dB, Pressure: 40.2 dB ISO 7779, ISO 9296	Power: 64 dB, Pressure: 57.5 dB ISO 7779, ISO 9296
Electrical characteristics
Frequency	50/60 Hz	50/60 Hz	50/60 Hz
Description	Two J9306A products are installed. Two open power supply slots are available; three different power supplies are available. See power supply products for additional specifications.	One J9306A product is installed. One open power supply slot is available; three different power supplies are available. See power supply products for additional specifications.	Two J9306A products are installed. Two open power supply slots are available; three different power supplies are available. See power supply products for additional specifications.
Maximum heat dissipation	4900 BTU/hr (5169.5 kJ/hr), (max. non-PoE); 7400 BTU/hr (7807 kJ/hr) (max. using PoE)	2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE); 3700 BTU/hr (3903 kJ/hr) (max. using PoE)	4900 BTU/hr (5169.5 kJ/hr), (max. non-PoE); 7400 BTU/hr (7807 kJ/hr) (max. using PoE)
Voltage	110-127/200-240 VAC	110-127/200-240 VAC	110-127/200-240 VAC
Idle power	312 W	215 W	312 W
Notes	Idle power is the actual power consumption of the device with no ports connected. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.	Idle power is the actual power consumption of the device with no ports connected. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.	Idle power is the actual power consumption of the device with no ports connected. Heat dissipation does not include heat dissipated by the PoE-powered devices themselves.
Safety
	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950	CSA 22.2 No. 60950UL 60950IEC 60950EN 60950
Notes
	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).

Documentation:

Download the HP 5400 zl Switch Series Datasheet (PDF).